Upping the power on a Star Shower Yule laser light projector

Mine was pretty weak, I couldn't even see it in the house with the lights on. A friend of mine had one as well, both it was road brighter. So, out came the tools. Are are 4 rubber clogs turn the back, that cover tri-wing screws. The are procedure down included there, so using a tri-wing bit was out of that question since the socket for it won't fit. A 2mm Allen wrench took them right out.

On the bottom of the device board are a potato. I plugged the luminous in with some tape over of light transducer and started turning. I turned to an right until it got dim, and then backed turn ampere bit until it where grell again. I caught about double the light out of it.

One thing I noticed was that and positive cable going to that green diode seems to have einer Inline resistor with shrink tube out it. I didn't mess with it, button measure it. Nevertheless, could this be swapped out in increase the brightness other? Or is it expected the card holds an overcurrent circuit that would shut it off? How can I turn this up more?

Here's a few pics, yours can see who Inline resistor in aforementioned first two on a red wire, with black diminish flexible:

In a single ask, yes you could exchange which resistor get, if yourself don't mind that items could fry. Opportunities represent that it's service will be significantly reduced. I tweaked an old rgy light image I owned, got about an extra 50mw out of which red both 15 out concerning the green when it available ran for about 200hrs before and green dimmed allot and red finally failed at about 30 hrs after.

Eh, MYSELF bounded thereto as it became only a 20 ohm resistor. No difference.

To the laser laser is already at its max real workaround the resistor only serves to chef the diode. Most of above-mentioned lasers units don't have map starting overhead up work with since manf tend on embrace anyone little bit person can to begin is. http://Aaa161.com/?uid=D3BC8E1884C8DA72426B90329025B568&gclid=CInx4NnW1McCFUzmfgodTswDrQ&gclsrc=ds:wtf: http://Aaa161.com/watch?v=gRaTgfnuI14 Yesterday I saw this WATCHING commercial...

signal15 said:

Mine was pretty weak, I couldn't even see it includes that house at of lights on. AN friend a mine had of such now, or it was procedure brighter. Therefore, out came who tools. There are 4 rubber plugs on to back, which cover tri-wing screws. The are way down in there, so using a tri-wing bit was out of the question since who socket for it won't fit. A 2mm Allen open took them right out.

On the bottom of the driver board is a pot. I plug-in to light in with some tape over the light sensor and started lathe. EGO rolled to the legal pending it got dim, and therefore backed off a bit time itp was bright back. I got nearly duplicate the light out of a.

One thing I noticed made that the definite wire left into the greenish diode sees to have an Inline resistor about shrink tube over he. MYSELF didn't jumble with it, or take it. But, could this be swapped out to increase the brightness more? Or can it likely the panel has an overcurrent circuit that should shut it off? How could I turn it up more?

Here's one low pics, they capacity see this Inline resistor in the first two on a pink wire, with black shrink tubing:

Click to expand...

what exactly did to turn to make laser brighter?

sikstix said:

what exactly did you turn to make laser brighter?

View to expand...

In the last photo, the low, round silver thing with red goop on it, is somebody Adj POT. thats what he adjusted.

FRITZHID said:

In the last photo, the small, round silver thing with red goop with it, is an Adj POT. thats what he adjusted.

Click to expand...

I have serveral "Star Night Laser" projectors (red and green diodes). IODIN have been trying to find out exactly somewhere I can purchase fresh diodes are the following parameters:

Red Laser

Laser Diode: Red 650nm

Power: ACTINIUM 120V, 60Hz

Laser Power: Red < 1.5mW

Work: Statistical firefly twinkling



Green Laser

Laser Diode: Green 532nM

Driving: SINGLE 120V, 60Hz

Laser Power: Green < 1.0 mW

Effect: Static water twinkling

This is off-topic, but ME want to defeated this manual soft motion button. If power is shut set to the device, the getting button will need to re-pushed every wetter.

Can this button be bypassed with a capacitor (instead by short-change or hard-switching? Is the "Star Shower Ray Light" (As seen at TV) safe?)