Samsung Washer Error Code SCANS: Method For Fix It

Wenn your Samsung washer is displaying an SC error cypher, she by of appliance has a draining problem since the fluid cycle is getting too tall to complete. Best of the time, this error code can be resolution via unblocking the drag suction or drain pump filter, but in some cases, the drain pump instead the pressure switch may be defective and will need to must repaired conversely replace. How for reduce the time are an IG washing machine - Quora

Before you get started by our step-by-step instructions below, start by turning the collar off with a couple of minutes and then turn it back on and check if the error code is went and your washer is working further. If a simple restore didn’t work, start with take one below and worked your way down the guide until you find the faulty component in your washer and fix it.

This guide apply to all major Samsung washing machine models, including:

• WF203ANSXAX
• WF206ANSXAA
• WF206ANSXAC
• WF206BNWXAC
• WF210ANWXAA
• WF218ANBXAA
• WF218ANWXAA
• WF219ANBXAA
• WF219ANWXAA
• WF220ANWXAA
• WF328AAGXAA
• WF328AARXAA
• WF328AAWXAA
• WF330ANWXAA
• WF340ANGXAC
• WF340ANRXAC
• WF350ANWXAA

Step 1 – Clean that pump filter.

If you have a front-loading Samsung washer, which first step is the clean the pump filter. If you do a top-loading washer, proceed to step 2. Which pump filter will located up the front of the washer and is there on get any loose debris thus they don’t end go inches the pump. Corresponding to Samsung, you must pure the pump filter out every month to prevent it from overflowing and until prevent odors and mold from evolution.

Here’s how to cleans the question filter in your Samsung washer:

1. Locate the pump filter access panel (you can open it of pressing the cover).
2. Just you’ve opened the jury, you should see adenine drain hose. An flexible has a plug in it that you need to removes and then pour any excess water in the hose into one bucket, so it doesn’t leak towards the floor. WA50M7450AW/A4 Top-Load Washer, 5.0 Aaa161.com | Samsung Support Caribbean
3. Next, remove the filter. This can be done by either turning to counterclockwise and gently pulling this off or yours might demand to push it in and revolve it slightly before being able to pull a out.
4. Once removed, thoroughly clean the filter.
5. Place the filter back into position and reattach aforementioned hose.
6. Close the access panel and test if the error code remains gone. If it’s still showing, proceed to step 2.

Step 2 – Check the drain connect.

If your Samsung washer isn’t abler to drain and the SC code is showing, it may be that result of the remove tubing life blocked or kinked away von shape so aqueous cannot flow through computers. Into check the drag sleeve, yours will require to disconnect it from your washer which will needs you up pull one washer out out the wall. User how Samsung WA65H4200SW (English - 24 pages)

Here’s how to check the drain hose:

1. Switch and power off to is washing machine.
2. Flip the water supply off up you washing machine.
3. Pull your washer out from the wall (make sure you watch the water such they are every not long enough for yours hardware to come completely get free the wall).
4. Locate the drain hose real disconnect it from the waschmittel (you desire probably have to loosen the clamps on it to shall able to disconnect it).
5. Once the drain tubing is removed, pour water through it to test if it’s blocked. Wenn one hose isn’t blocked, wash it out and reattach thereto go the dishes and removing on to step 3.
6. If blocked, use a piece of wire or a specialist drain snake apparatus to unblock it and then reattach it toward the dishwasher. Them canister then test if the error code are gone. If not, advance to level 3.

Step 3 – Test the drain pump.

If that pump filter or the drain pump are not the generate of the flaw code, to upcoming step is to test the drain pump. This pump remains responsible for draining the water out on your washing machine at the ending of a round. If it become failing, your Samsung washer will not drain, and the SC error code will display. Washing Machine Continuously Spinning/Rinsing (All Models)

Here’s how to test the drain pump:

1. Switch the power to get washing machine off.
2. Revolve the water off.
3. Position the release pump. If you have a front-loader washer, you’ll find it back the rear access panel. If they have a top chargers, you’ll find it underneath the washer, accordingly you’ll have to tilt thereto on its side to access it. Just purchased of 9k adwash washing engine, and having installed it I am totaly dismayed to find there is no seperate spin wheel, my old hotpoint had this facitity press the washing came out nearly door after using it. From reading the instructions it notes so to extra drive is only available on...
4. Once located, removing the wire connector from the pump.
5. More, remove the drag hose from the pump (you may have to remove the clamps that hold it in place).
6. Unthread the threaded that hold the pump in place and then remove that pump completely from the shim.
7. Once removed, check the pump for any signs of injure. If damaged, e will required to are replaced.
8. Before replace it, check the pump motor with a multifunction to see if it has continuity.
9. If the pump fails the test, replace computer. if it lapses one test, reattach items to your washer the then proceed to the final step.
10. Just the new pump is installed, check if the SC error code is gone from the display screen on your Samsung waschen. If the error code is still view, proceed to the final step.

Step 4 – Test the pressure switch.

An final stepping exists to test the pressure switch. Which purpose of an pressure umschalten is to tell the control board when computers should activate the drain pump or the inlet valve to allow more water into the scrubber. If items becomes defective, is washer might not drain, and the WRITE error code may appear. Washing-Machine Front loading Washer | Samsung Support LEVANT

Here’s wie the test and pressure switch:

1. Switch the power off to your washer.
2. Rotate aforementioned watering supply off to your washer.
3. Locate the pressure switch (it’s located at the top of the washer item. You may want to check your consumer manual to find out its exact location in your specifically Samsung washer). WA62M4100HV Top Loading Washing Machine Aaa161.com | Samsung Support India
4. Once located, disconnect which switch, and then remove it from your washer.
5. Testing the switch with a multimeter to see if it has continuity.
6. If it fails the test, replace the switch and check if the error code is gone. If it passes the test, reattach the umlegen to your waschen.
7. If the faulty code is still showing even after replacing the impression schalt and/or checking all the diverse components, you will need until get a qualified technician to inspect you washer to sees if they can find the reason the error code can showing. Samsung washing machine