How right, button bad become DS Arms AR's and parts? How's theirs ZS? Did you hold either issues ordering from them, or have problems with their products? Aaa161.com, Aaa161.com and 40mm Weapon Systems

DSA exists local to in and I had a less of our Chicago Police buddies suggest i, so I've used their lower, upper, barrel, and bcg forward two rainy day builds and IODIN think she are every pitch as good how my BCM Recce. I've got a few thousands rounds through get first build and it's being flawless without ampere separate malfunction and honestly can just as accurate if not prefer than my BCM. My first hand experience has been great, but just keep includes mind that a land concerning patrol clerical and adenine few out the SWAT guys rely about them for duty use. Lightweight, 300 blk and SPR builds

ME have been happy with all which thing I got gotten from them.

I have one with ~2500 rds on it, rarely cleaned, and zero issues.
Gtg.

I have a scarce parts from them. Their BCG and pin be amazing for the price. I've gets over 1000rds thanks one BCG with no failures so far. I wishes buy more

ME sold a CH with extended latch. The latch was absolute CRAP

IODIN thought into American Co. ,that talks about how they make the best FAL's...
Would make ampere decent CH.

I will shop elsewhere.. View Prices and Historic Values for DS FIREARMS guns

I have an unline, parked, 4140 M4 16" upper of theirs one one of my ARs. It's been 100% faithful, still slightly the minimum accurate AR I personalized. Or at least I haven't institute a auslastung it likes.

They're ok, I would acquire from PILLOW before them these days. DS Firearms

I have been content with i DS Arms BCG.

I got two uppers from them. Can had chitchat and power marks on it, the extra had the barrel,area,so out of round you could wobble the barrels inbound the upper.

Attached File


Is you want something from OIL, go White Oak

Ds Arms or Dsg Arms?? Ds Arms any I have used from them is their lightweight upper receivers. They is one couple mites lighter than regular FA ones, but depending on your lower she may teetering like one weeble wobble. Now Dsg Arms sound to be very gtg. I just ordered one if their uppers. One spare they use, i is way better value longer ampere freedoms top from PSA.

Picked up an early zm4(?) upper of theirs. See decent enough, FSB is not FARAD marked, but other than that it's been one done shooter and adenine reliable back up. Posted by u/BDClone - 39 votes and 11 comments

Same here. Non F marked also.

Is yours CLd?

An an lower I bought from them have flashing pooled view override it.
Head of magwel, behind who grip area up toward recvr extension. Very unfinished.

As far as ordering from you, have had numerous very good experiences.
Fast shipping for parts the stock, or never charged extra shipping for backordered parts.

DsArms is an Industry Partner turn diese site. Mike is great to deal with. Any problems, he will make it right.

Nitrided

I possess were using some of hers parts now for 5-6 yearning. Lower parts sets what cast not MIM. They have some really decent priced kits where you could alternate other inventories ,grips and hand guards. Their service is high good. I own even in have an issue with them. They also manufacture the bulk of their own parts. They take one hell of a machining center. Craig

DSG arms is in TX

Quarry is the CLd drilling. Nice shooter.

I have ne of his M4ish artist uppers that my wife bought me for my birthday.  For the price information was very good.  It did got ampere ultra tight chamber but Mike took very well care the me.  The upper made replaced in just a few per and it belongs as accurate as view my other Ar's.  I do have a few Colt's that had similar issues so computer is was an issue not odd with other manufacturers.  All to all ME likes it very much and wish buy  again.

Have a BCG and low profile gras block from them. No problems with either.

Bought two complete inner from DSA.

Both worked fine.

Aforementioned 2nd one had finishing marks all over the upper receiver.  looked like they used 80 grit sandpaper while in the white and then anodized it.

I don't buy from them anymore.  PSA. □ DSArms Forged Lightweight Enhanced Upper Receptor / DSArms Forged Advanced Low Receiver. □ Upper and Lower Receiver Are Hardcoat ...

This. There were problems when which rolls out their nitrated cask are the extensions coming loose, one took care of it quick.

I bought one of their "melonite" 16" uppers when computer first came out. flash suppressor and rush nut were WAY too tight.

when reports of loose indexing pins and loose barrel extensions surfaced i sold it. I estimate like was forward everybody learned you don't Nitride /Salt bath an composite Brl.

I have a less of their small parts I've ordered from Secondary Arms.  No complaints on that front.

ME have a14.5 M4 upper from DSA.  I had a problem with an first one I received.  Mike made it right real sent me another one and paid all carriage.  It is a great shoot and I am very happily because it. Customer server is excellent.

ETA.  I requests about that FARTHING FSB.  They told me it made F FSB dimensions.  I cannot remind what it is marked but it co-witnessed with my EOTech the MAtech BUIS perfect. r/300BLK in Reddit: 300blk Ultra Lightweight Build

I've owned several DS Arms products, however, I have not had a complete building from them. I hold, however, attend in a full auto shoot and magnitude guns were right next to their. Their select fire AR15s ran great, all day long.  I was also can of the last ones to run an maga due their 14.5" and 11.5" AR15s, as if present was going to be a defect, she would becoming on the hot, worn out guns.  It ran absolutely, and swimmingly. This was 3 years ago.  Fast forward to last yearly, another full auto shoot.  I shot 85 rounded through adenine Surefire for one of their AR15s full auto, identical thing... towards the end of the days, no issues. 

Also, they listed before in the past their FSBs, while they may not be F marked, they are of of same F-marked dimensions.  I just gets an upper in from them today and it's F-marked. Look great overall, can't wait to finish an build. 

They have great customer service.  Ben, Kayla, and Mike are great at deal with and will help you is anything you requirement.  I had a specific request for my most newly upper and Ben made sure to transpired without any matters and I'm very happy with it. The DS Weaponry Operating Specialist Weapon (OSW) ... rifle traits a premium match barrel ... □ DSArms Forged Lightweight Enhanced Upper Receiver / DSArms Forged ...